RF demystified – understanding wave reflections
Question: Wave reflections—why are they important to understand in RF designs?
A guide for choosing the right RF amplifier for your application
Question: How do I choose the right RF amplifier and what are their differences?
A new, better way to optimize a signal chain with a continuous-time sigma-delta converter
Question: Why should I consider using CTSD ADCs to improve my signal chain design?
Sponsored content by Ecomal Europe GmbH
A reliable European distributor
When is the most critical phase in the launch of a new electronic product? Is it development, which regularly takes place under great time and cost pressure? Or is it the transition to series production, when large quantities of components have to be delivered quickly - with precisely specified characteristics and exact timing? Each of these phases confronts companies with its own challenges. The support of a competent and reliable distributor often makes all the difference.
Keeping EMI from LED drivers under control
Question: How can I reduce electromagnetic interference when using LED drivers in lighting design?
Generating very low voltages with standard regulators
Question: What is a good solution for generating a tiny dc supply voltage of a few hundred millivolts?
Design of an adjustable voltage output using a push-button digital potentiometer
Question: How could I use a digital potentiometer to generate an adjustable voltage output?
Energy storage using supercapacitors: How big is big enough?
Question: Can I use a simple energy calculation when selecting a supercapacitor for a backup system?
Sponsored content by PEI-Genesis
Cinch connectivity solutions 26482 series connectors
Cinch's "MS" series connectors are not just meeting but exceeding the requirements for MIL-C-26482 Series I Solder qualification, earning their spot on the U.S. Government's Qualified Product List. With nine shell sizes and over thirty insert arrangements, featuring pin or socket contacts, these connectors offer versatility like never before.
Wide voltage range automotive circuit protector
Question: Are there overvoltage and undervoltage protection devices available, especially for automotive applications?
RMS Power vs. Average Power
Question: Should I use units of root mean square (rms) power to specify or describe the ac power associated with my signal, system, or device?
Ultralow noise, 48V, phantom microphone power supply using a tiny DC-to-DC boost converter
Question: Can I produce a compact, ultralow noise, phantom power supply (48 V) from a 5 V, 12 V, or 24 V input?
LTspice Audio WAV Files: Using Stereo and Encrypting Voice Messages
Question: Can you utilize stereo data and encrypt voice messages with LTspice audio WAV files?
On building physically accurate analog switch macromodels
Question: Can I improve the LTspice® model of an analog switch in case my analog design contains switches and muxes?
Manipulating MCU SPI interface to access a non-standard SPI ADC
Question: Can I access a nonstandard SPI interface with my MCU?
Adjusting the gain of a fixed-gain difference amplifier
Question: Is it possible to increase the gain of a fixed-gain difference amplifier?
Inductor current measurement in switched power supplies
Question: How do you measure inductor current?
A simple way to measure temperature using one GPIO digital interface
Question: How can I make an analog measurement if I only have a single GPIO left on the FPGA/microprocessor for my system?
Sponsored content by Multi Leiterplatten GmbH
PCBs: price reduction of up to -50.3% through AI
Thanks to the increased use of AI in production preparation, Multi-CB, a leading European PCB specialist, has been able to permanently reduce the prices for 1- and 2-layer PCBs. The price for a half Eurocard (80x100mm), for example, is now € 14.80 instead of € 29.80. Due to the process, the price reduction has the most significant effect on small quantities, although medium quantities are also benefiting.
Bootstrapping a low voltage Op Amp to operate with high voltage signals and supplies
Question: Can I bootstrap a low voltage amplifier to get a high voltage buffer?
How to convert light intensity into an electrical quantity
Question: How could I measure the light intensity of different light sources?
Guidelines for placing the inductor on a switch mode power supply printed circuit board
Question: Where Should the Coil Go?
Load more news