Sponsored content by Electrolube
Design Challenges And The Impact On Coating Success
Phil Kinner, conformal coatings technical director discusses how As assemblies become ever more densely populated, the need to carefully consider your conformal coating process is becoming increasingly more important.
As assemblies become ever more densely populated, and housing /casing designs become more permeable to save weight, the use of conformal coatings is becoming essential to protect the assembly from its operating environment and ensure acceptable reliability for the application intended, especially when operating in hostile environments. In my previous columns, we have covered some of the fundamental considerations of conformal coating selection and performance, examined key benefits of different types of coatings and explored their limitations. For this month’s column, I am going to concentrate on some essential factors regarding the challenges board designs can pose on designers, in order to help you implement a more successful coating operation. So, let’s look at issues that may arise with coating coverage, cycle times and coating flow. Board Design Challenges The design of the board can have a huge impact on a successful coating operation, both by determining which methods can actually be used, as well as the degree of coverage that can be achieved within the required cycle time. I’m going to focus on selective coating, being the most common application method, where masking is minimised if not eliminated, but most of the principles will translate to other coating application methods. In lean manufacturing, the coating cycle time is often the key requirement, ensuring the production takt time can be met, thus maintaining a balanced line. Given that coating is often one of the latter processes in the production line, it is often advantageous for the coating cycle time to be faster than the overall line takt time to ensure any accumulated production can be cleared as rapidly as possible, should any previous operations suffer a stoppage. In general, the less areas there are on a board that must be free from coating, the faster the coating cycle time will be. Should the coating cycle time be too long, then a decision can be made to either determine the most vulnerable parts of the assembly and focus on that area in the available cycle time, or to split the coating across several workstations. Coating Cycle Time Coating cycle time is clearly very important to the balance of the production line, so what kills coating quality and cycle time on a typical selective coating line? Selective coating machines deposit a stripe of coating material, that can be programmed to stop and start on demand. Stripes of coating can be deposited to create a coating pattern, avoiding areas such as switches, connectors and test points, which must not be coated to prevent interference with form, fit or function. The coating stripes deposited are usually in the 8-15mm range, for optimum accuracy and minimizing overspray and splashing. When the area to be coated is less than 8mm in width, then it is necessary to utilise a dispensing step, which is a cycle time killer. Due to the combination of machine X/Y positional accuracy, material fluid dynamics and component topography, 2-3mm is usually as close to ‘keep out’ areas as anyone would be comfortable coating for a repeatable process. In summary, ‘must coat’ and ‘keep-out’ areas positioned within 2-3 mm of each other present a problem. Dispensing is also required, representing another process step adding to cycle time. Coating Flow In manufacturing, for many coatings, it is difficult to limit the flow of coating from the application site to adjacent sites. Most coatings will have some level of capillary flow (often referred to as wicking), taking the coating to unanticipated areas. Therefore, components which MUST be coated should not be placed in proximity to components with MUST NOT be coated. Coating flow is also an important consideration on low standoff bottom-terminated devices, such as BGAs or QFNs, which may also have microvias under them. Coating can wick under the parts and then down the vias to the opposite side of the assembly. To avoid this problem, the vias under low standoff components can be tented with solder mask or have the vias filled with solder or a suitable via-fill material. Of course, since conformal coating can reduce the solder joint lifetime of bottom terminated devices, deliberately coating beneath these devices should be avoided. Keep in mind that liquid coatings will flow somewhat during the coating application process, so placing a keep out zone at the base of a tall component, such as an electrolytic capacitor, will create a lot of problems in manufacturing as the coating flows down the tall part into the keep out zone. Engineering drawings or quality control documents should be very specific on what coating “anomalies” are defects requiring disposition and those which are primarily cosmetic. For many years in the industry, anything that looked different in the coating was considered as a “defect”, requiring ascetically perfect assemblies. While possible, such requirements often drive up the cost of coating and often have no impact on assembly reliability. Designers should be aware that coating the edges of assembly is not considered as value added for most applications. Most design standards do not allow inner layer circuit traces to be closer than 0.63 mm from the edge of the board. The act of routing the board edges results in smearing the epoxy resin over the cut glass fibers or the reinforcement material, sealing off the inner layers. A designer might specify coating board edges where such sealing does not occur, such as with V-scored, punched, or sheared edges. Understanding the dynamics of what affects what on the surface of the board during the early-stages of design will go a long way in helping you achieve a successful conformal coating operation. In turn this will also help avoid potential disasters in other areas of production too. If you have any questions, or would like more information about conformal coatings, then there’s a wealth of experience to call upon from our Technical Support Team members who will be more than happy to answer your queries and offer expert guidance.
Norautron Suzhou inks new contract with Efore Norautron Suzhou Co.Ltd announces a new cooperation with Efore Electronics Suzhou Co.Ltd.
Sourceability appoints new managing director for APAC Semiconductor veteran joins the management team of digital supply chain solutions provider.
POET and Sanan IC to form a joint venture company POET Technologies and Xiamen Sanan Integrated Circuit (Sanan IC), a wholly owned subsidiary of Sanan Optoelectronics, have signed a definitive joint venture contract.
From wafer sawing to the finished packaged component Encapsulation is essential for the reliability of a component, as it needs to protect the sensitive silicon and bonding joints even under variable environmental conditions or temperature ranges. High-quality packaging is therefore indispensable to ensure the functionality and reliability of a component and the entire device.
Sponsored content by NCAB Group BeneluxHow to design a high speed PCB! It wasn’t that long ago when the word “high speed” didn’t exist in the vocabulary of PCB designers. Thinking back for example at the 90’s and 00’s, the speeds they used were much slower. In 2005, 3 Gbps was considered the typical high speed data rate, but today engineers are dealing with 10 Gbps, or even 25 Gbps.
Avnet Silica names Gilles Beltran as president Beltran succeeds Mario Orlandi who takes on global assignments in Avnet.
While close to settling legal case with US, UMC to focus more on foundry business UMC has announced today (Oct. 22) that the legal case against the company filed by the U.S. Justice Department for stealing trade secrets could now be resolved as soon as possible, according to TrendForce’s latest investigations.
Kitron’s record performance continues amidst the pandemic The EMS provider reported strong growth and record profit for the third quarter of 2020 – mainly driven by the Medical devices, Defence/Aerospace and Industry sectors.
Huawei opens new R&D centre in Hungary The Chinese telecom company opened the R&D Center in Budapest as it’s celebrating its 15th anniversary in Hungary.
Sponsored content by JBCHigh Quality & efficient fume extraction is not only important to meet workplace regulations It's also important to ensure the safety and health of everyone. Soldering fumes and gases may be one of the main causes of potential health problems at any soldering workplace without a proper fume extraction. To protect all employees and their health, keep the following suggestions in mind!
SkyWater is looking to lease a 200 mm fab in Florida Having just completed the expansion of its Minnesota facility, SkyWater does not seem to be done adding to its footprint. The company is looking to take over the Center for Neovation, a 200 mm semiconductor manufacturing facility.
Airbus Ventures invests in Singapore startup Airbus Ventures latest investment has led the company to Singapore and Zero Error Systems (ZES).
General Motors invests in its electric future General Motors says that its Spring Hill, Tennessee assembly plant will begin the transition to become the company’s third vehicle manufacturing site to produce electric vehicles. The automaker also says that it will invest heavily in five Michigan plants.
Hisense Gorenje to start European production of TVs in January As we move into the next year, Hisense owned Gorenje Group will start production of TV sets for the European market at its plant in Velenje, Slovenia, as part of the new Hisense Europe Electronic company.
Wistron to expand in Malaysia – acquires Western Digital plant In a filling on the Taiwanese stock exchange, the company has disclosed that it will acquire a plant from Western Digital (WD) in Malaysia via its subsidiary Wistron Technology (Malaysia).
SK Hynix holds second highest NAND market share via acquisition of Intel’s NAND capacity SK Hynix has announced today (Oct. 20) that it will acquire Intel’s NAND Flash business and Dalian-based Fab 68, which is dedicated to 3D NAND Flash production, for USD 9 billion.
Harwin addresses increased demand for Hi-Rel connectors with new facility The expansion at the manufacturer’s Portsmouth headquarters in the South of England will increase the company’s production output by 30%.
Blackstone has found the location for its battery cell production The Swiss company, focusing on battery technology and battery metals, says that a decision has been made on the location of its battery cell production facilities for its subsidiary Blackstone Technology GmbH.
US foundry makes the case for a secure domestic chip production SkyWater Technology’s expansion in Bloomington, Minnesota, has progressed quickly. The project started less than a year ago and on October 12, the company held a ribbon-cutting ceremony to celebrate the completion of the expansion.
Wistron continues Taiwanese expansion – sets up third R&D office The Taiwanese manufacturer has announced that it is adding to its set up in the country. The company will establish and R&D office in Kaohsiung, Wistron’s third R&D office in the city.
Terry Gou addresses Foxconn's Wisconsin investment “Foxconn will remain committed to the completion and continued expansion of our project and investment in Wisconsin as long as policymakers at the federal, state, and local levels remain committed to Foxconn,” Terry Gou says.
Volkswagen invests to up the automation of several plants The Volkswagen Passenger Cars and Volkswagen Commercial Vehicles brands are working flat out on the transformation to the e-mobility era and the conversion of plants to e-mobility.
AT&S appoints Simone Faath as CFO With the appointment of Simone Faath as CFO, the AT&S Management Board is now complete again.
SK hynix to acquire Intel NAND memory business The two parties have signed an agreement under which SK Hynix will acquire Intel's NAND memory and storage business for USD 9 billion.
High power quarter brick isolated DC/DC converter addresses demands of energy-conscious data centers Continuing to extend its portfolio of high-density DC/DC converter solutions with built-in digital interfaces, Flex Power Modules introduces two variants of the new BMR491 series.
Wipro to acquire Eximius Design The information technology specialist says it has signed a definitive agreement to acquire Eximius Design, an engineering services company with strong expertise in semiconductor, software and systems design.Load more news